CL-W114-OS00BL-A | ThermalTake C1000 Opaque Coolant - 1000ml, Black

Overview

C1000 Opaque Coolant Black

The latest C1000 Opaque Coolant launched by Thermaltake is used as anti-corrosion protection fluid and heat-transfer medium for PC water-cooling. Made in Germany, the C1000 Opaque coolant is virtually odorless, non-flammable, and high performance liquid, offering superb protection for copper, nickel, brass, and aluminum. Choose from eight vivid colors: red, green, blue, orange, yellow, white, purple and black to brighten up any build with Thermaltake.

Tt LCS Certified

“Tt LCS Certified� is the hallmark that ensures first-class performance from the best features and fitment. A certification exclusive to Thermaltake, it sets the benchmark for all true LCS chassis and is applied only to products that meet our stringent design standards for delivering what hardcore enthusiasts demand. The Tt LCS certification is a way for Thermaltake to designate to all power users the chassis which have been tested for best compatibility with extreme liquid cooling configurations.

German-Made Anti-Corrosive Solution

Being non-flammable, the C1000 Opaque Coolant is a ready-to-use cooling solution with at least 3 years shelf life in airtight containers, providing great performance while preventing the entire cooling system – copper, brass, nickel, and aluminum – from corrosion.

Biodegradable Material

The C1000 Opaque Coolant is classified in water hazard class 1 (low-rate endangering) according to German water hazard regulations. The product is readily biodegradable.

Vivid Application

Thermaltake C1000 Opaque Coolant is designed specifically for PC liquid cooling systems. Featuring anti-freezing, anti-rusting, and water scale prevention, the C1000 non-transparent coolant delivers great thermal efficiency and further reduce the temperature of the system.

Caution

May be harmful if swallowed, may cause birth defects. May cause respiratory tract, eye and skin irritations. Keep out of reach of children. Avoid breathing any vapors or spray mists. Use with adequate ventilation. Avoid contact with skin and eyes. Keep container tightly closed when not in use. Wash thoroughly after handing. Store in a cool place.

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:

1. To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
2. Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
4. Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup:

1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system copper, brass, nickel, aluminum, and steel from corrosion.
2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
4. Fill the reservoir to the top as it will prevent air from going into the pump
5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
6. Place some paper towels under fittings and joining points to test for leaks.
7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
8. Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
9. Coolant might fade over time
10. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
11. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your
12. Fill the reservoir to the top as it will prevent air from going into the pump
13. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
14. Place some paper towels under fittings and joining points to test for leaks.
15. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop

Specifications